Moduł uniwersalny mikrokontrolera Cortex-M3 NXP LPC1768FBD100, leżak magazynowy.

Na płytce piny procesora wyprowadzone na złącza oraz listwy pinowe, złącze miniUSB, gniazdko Ethernetowe i kontroler ATHEROS AR8030.

Sądzę ze może służyć jako płytka developerska.

Po podłączeniu do laptopa przez kabel USB zapalają się diody na płytce a następnie część gaśnie.
Na laptopie płytka jest widoczna jako urządzenie USB w następujący sposób:

$ sudo lsusb -v -s 3:5

Bus 003 Device 005: ID f1ef:0a09

Device Descriptor:

bLength 18

bDescriptorType 1

bcdUSB 2.00

bDeviceClass 239 Miscellaneous Device

bDeviceSubClass 2 ?

bDeviceProtocol 1 Interface Association

bMaxPacketSize0 64

idVendor 0xf1ef

idProduct 0x0a09

bcdDevice 1.20

iManufacturer 1 LPCUSB1

iProduct 2 LPCUSB2

iSerial 3 LPCUSB3

bNumConfigurations 1

Poniżej parametry ze strony producenta procesora:

• Arm® Cortex-M3 processor, running at frequencies of up to 100 MHz

• Arm Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC)

• Up to 512 kB on-chip flash programming memory

• Up to 64 kB On-chip SRAM

• In-System Programming (ISP) and In-Application Programming (IAP)

• Eight channel General Purpose DMA controller (GPDMA)

• Ethernet MAC with RMII interface and dedicated DMA controller

• USB 2.0 full-speed device/Host/OTG controller

• Four UARTs with fractional baud rate generation, internal FIFO, and DMA support

• CAN 2.0B controller with two channels

• SPI controller with synchronous, serial, full duplex communication

• Two SSP controllers with FIFO and multi-protocol capabilities

• Three enhanced I2C bus interfaces

• I2S (Inter-IC Sound) interface

• 70 General Purpose I/O (GPIO) pins with configurable pull-up/down resistors

• 12-bit/8-ch Analog/Digital Converter (ADC) with conversion rates up to 200 kHz

• 10-bit Digital/Analog Converter (DAC) with dedicated conversion timer and DMA

• Four general purpose timers/counters

• One motor control PWM with support for three-phase motor control

• Quadrature encoder interface that can monitor one external quadrature encoder

• One standard PWM/timer block with external count input

• Low power RTC with a separate power domain and dedicated oscillator

• WatchDog Timer (WDT)

• Arm Cortex-M3 system tick timer, including an external clock input option

• Repetitive interrupt timer provides programmable and repeating timed interrupts

• Each peripheral has its own clock divider for further power savings

• Standard JTAG test/debug interface for compatibility with existing tools

• Integrated PMU (Power Management Unit)

• Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down

• Single 3.3 V power supply (2.4 V to 3.6 V)

• Four external interrupt inputs configurable as edge/level sensitive

• Non-maskable Interrupt (NMI) input

• Wake-up Interrupt Controller (WIC)

• Processor wake-up from Power-down mode via any interrupt

• Brownout detect with separate threshold for interrupt and forced reset

• Power-On Reset (POR)

• Crystal oscillator with an operating range of 1 MHz to 25 MHz

• 4 MHz internal RC oscillator trimmed to 1 % accuracy

• Code Read Protection (CRP) with different security levels

• Unique device serial number for identification purposes